Page Numbers: Yes   X: 530   Y: 10.5"   First Page: 5
Columns: 1   Edge Margin: .6"   Between Columns: .4"
Margins:   Top: 1.3"   Bottom: 1"
Line Numbers: No   Modulus: 5   Page-relative
Even Heading:qk40(635)
MAXC Room Power Down Procedurey756qck40\30f1
Odd Heading:qk40
Power Upy756qck40\8f1
4.	Start Up Sequence:x6e12jk40\f5b21B
	Close only those circuit breakers on panels marked Maxc, Maxc-A, & Maxc-B, that were opened
	during the initial powerdown sequence.	x6e12jk40\7ui4UI
	Twinkle	(Should be started first for Date & Time source to other systems.)	x6e12jk40\1b7B1bi66BI
Turn on AC Power and spin up disks	
Boot ALTO	
Type GATEWAY<cr>	(2 minutes to come on)	l5468x6e12jk40
	NOTE 5:	Don't bring anything else up until message "Gateway in operation" appears on
		Twinkle screen, or 1 minute after screen turns blank, whichever occurs first.	l5468x6e12jk40(0,6350)(1,8128)\1bi4B1b2BI1f1 156f0
 Remaining machines can be started in any order (or simultaneously).	x6e12jk40(635)\1bi67BI
	DLSx6e12jk40\1b3B
Set CKT breaker	
Spin up disk	
Boot ALTO	
Type DLSCONTROL	l5468x6e12jk40
	Juniperx6e12jk40\1b7B
Turn on ALTOs	
Spin up Diablo disks	
Turn on Trident disk AC power	
Spin up Trident Disks	
Boot
Type @RunServer<cr>	l5468x6e12jk40
	Maxc1		(Ref. Sections 3 & 5, Maxc Operations)	x6e12jk40\1b5B2i22b15B1I
Turn on NOVA power (key switch)	
Spin up disk and push red protection light	
Set front panel NOVA switches to 100040	
Toggle RESET	
Toggle PROGRAM LOAD	
Turn on all Processor and Memory cabinet power supplies	
On the Nova terminal (Infoton), issue the command:		POWER ON<cr>	

Turn on Disk drive AC power (in rear) then front panel switches.	l5468x6e12jk40
	WARNING:	Wait at least 10 seconds between spinning	
			up each	 drive to allow for the starting surge.	l5468x6e12jk40(0,6350)\1bi8BI
Normally the configuration is set up properly; just type MIDAS TENGO.	
See Section 5 & 6 of Maxc Operations for abnormal situations.	l5468x6e12jk40(635)\92bi15BI
	Maxc2x6e12jk40\1b5B
Turn on ALTO	
Spin up ALTO disk	
Turn on all Processor and Memory cabinet power supplies	
Boot the Alto and run the Midas subsystem.  With the left mouse button,	
succesively select the menu items "Power On", "Both", and "Do-It".	
Turn on Disk drive AC power (in rear) then front panel switches	l5468x6e12jk40
	WARNING:	Wait at least 10 seconds between spinning	
			up each drive to allow for the starting surge.	l5468x6e12jk40(0,6350)\bi9BI
Normally the configuration is set up properly; just type MIDAS TENGO.	
See Section 5 & 6 of Maxc Operations for abnormal situations.	l5468x6e12jk40(635)\92bi15BI
After all disk drives are ready you may start AltIO and start Tenex by	
selecting "Run-Prog", "Tengo" with the mouse.	l5468x6e12jk40(0,6350)
	Ivyx6e12jk40(635)\1b3B
Turn on ALTO	
Spin up Diablo disk	
Turn on Trident disks AC power	
Spin up Trident Disks	
Boot
Type IFS/F<cr>		    NOTE 6:	The /F is temporary - see Ivy operation instructions
										(next to terminal) for current procedure.	l5468x6e12jk40\115bi7BI1f1 104f0
	Doradosx6e12jk40\1b7B
Turn on Breakers (that's all)	l5468x6e12jk40
	Impx6e12jk40\1b
Should restart by itself.  Call NCC to verify correct operation.	l5468x6e12jk40
Referencesx6e36k120\b
1.	Edward R. Fiala, Charles M. Geschke, and Edward Taft, Maxc Operations, XEROX, January 30, l981.	l3696d2992x3e6jk40(0,3712)(1,65535)\57bi15BI