Page Numbers: Yes X: 527 Y: 10.5" First Page: 31
Columns: 1 Edge Margin: .4" Between Columns: .4"
Margins: Top: 1.3" Bottom: 1"
Line Numbers: No Modulus: 5 Page-relative
Odd Heading:

Maxc OperationsOperating Tenex Microcode from Midas

Even Heading:

Operaating Tenex Microcode from MidasMaxc Operations

10. OPERATING TENEX MICROCODE FROM MIDAS

A.Reset is accomplished by typing

21;G

to Midas. The effect of this is to put the machine in monitor mode, to clear the interrupt system, the APR, the processor flags and the disk system. However, Nova peripherals aren’t affected, nor are the accumulators or PC affected. If AltIO is called after RESET the processor will start at its starting address (pointed to by absolute location 7).

B.Starting at an arbitrary PDP-10 location n is accomplished by changing the contents of PC (which is on the display) to n and then typing

REMAPPC:(Midas types out the value m of REMAPPC)
"AltIO", "Do-It"

C.The PDP-10 accumulators are LM 0, LM 1, ..., LM 17 and can be examined and changed in the usual way from Midas.

D.The PDP-10 flags are in the left-most 13 bits of the F-register on the display. If you change these from Midas, don’t change the other 23 bits of F.

These and other interesting bits of F are as follows:

BitDefinition

0Overflow
1Carry 0
2Carry 1
3Floating overflow
4Byte increment suppress
5User mode
6PARC mode (replaces PDP-10 user I/O mode)
7Call from monitor (see JSYS, UMOVE, and Pager addendums to PDP-10 System
Reference Manual)
8-10Machine mode (0=PDP-10, 1=Byte Lisp)
11Floating underflow
12No divide
13Pushdown overflow
14XCT0
15XCT1
16XCT2
17XCT3
18Incompatible
19PI system is active
20PI cycle in progress
21MONALT - Temporary flag used by map loading microcode
22THIRDPT - Temporary flag used by map loading microcode
23Unused
24TTYBSY - console teletype output busy
25LOGF - enables main loop "LOGI", "BRKI", or "TRACEI" path
26PICYCLE
27CUM
28MICRO
29IENABLE
30Unused
31NOVA - Nova/Alto has left an interrupt request
32K
33J
34H
35G

E.The interrupt system state is given by the following:

PISTAT[29,35] have 1’s when interrupts are in progress on the corresponding PI levels[1,7]. PISTAT[22,28] have 1’s when interrupts are disabled on the corresponding PI levels.

SM 600 to SM 643 contain in bits 12-35 the interrupt locations corresponding to devices 0 through 35. The device assignments are in Maxc document 11.

SM 644 to SM 652 are the interrupt-enabled bit tables for priority interrupt levels 1 through 7. 1’s in each word indicate that the corresponding device (bit 0=device 35, bit 35=device 0) is enabled for interrupts at that level.

MICINTS contains 1’s for each device which has requested an interrupt. (However, OVF, FOVF, and PDOVF are recomputed from F for each instruction, so their state in MICINTS isn’t important.)

F.The microcode consistency "Checker" uses four variables CSUMD, CSUM0, CSUM1, and CSUM2 which contain checksums for all constants in the microprocessor’s IM, DM, DM1, DM2, and SM memories. CSUMD is an overall checksum (for detection of errors) while CSUM0-CSUM2 contain 18 6-bit bytes each of which is a checksum in a Hamming code. The checker computes the address which is clobbered assuming only a single word is wrong.

When newly assembled microcode is loaded for the first time on Maxc2, these checksums are computed and dumped automatically by "Midas Init". Subsequent runnings of the TENLOAD, MEXECGO, and TENGO command files check the newly loaded system against these constants, and crash on errors. Also the CHECK JMC does this (executed during Tenex initialization).