ChipNDale FOR INTERNAL XEROX USE ONLY ChipNDale 2.3 An interactive editor for VLSI designs MOS Designer's introduction Release 2.3 Ch. Jacobi, Kim Rachmeler (March 19, 1986) Filed on: [DATools]CDDoc23>ChipNDale.tioga c Copyright 1983, 1986 Xerox Corporation. All rights reserved. Abstract: ChipNDale is an interactive graphic layout tool made to run in Cedar. This document is an introductory reference for users creating or editing VLSI designs; there will be other documentation describing additional utilities like creating checkplots, masks, or CIF output, and doing design rule checking. Programmers who want to access ChipNDale from a program should read the additional documentation available for these purposes. XEROX Xerox Corporation Palo Alto Research Center 3333 Coyote Hill Road Palo Alto, California 94304 For Internal Xerox Use Only Contents 0. Introduction 1. General Definitions and Descriptions 2. ChipNDale Viewer Commands 3. ComandTool commands 4. User Profile Options 5. The Outside World 6. ChipNSil ChipNDale's documentation is divided into several main files: ChipNDale.tioga This text. Reference guide for interactive use of the ChipNDale editor for the technologies CMos, NMos, and ChipNSil. ChipNDaleTools.tioga Reference guide for interactive use of some other ChipNDale related tools. Some more tools will have separate documentation, stored with the tool directly. This document tells you for example how to make hardcopies. ChipNDalePrograms.tioga Reference guide for creation of ChipNDale designs from programs. That guide is a mixture of a guide for tool creation, technology creation and simple creation of particular ChipNDale designs from programs. CDCrib.tioga Crib sheet. ChipNDale-Registration.tioga To be used by implementors. Meta documentation about registered features telling where the real truth is stored. ChipNDaleMessages.tioga A unstructured list of messages about ChipNDale. Further tools may have their own documentation. Since ChipNDale is an open system it is not posssible to completely list all its available tools. Uncomplete list: CDExtrasDoc.tioga Doc for some extra modules. 0. Introduction 0.1. History ChipNDale1 is the ultimate interactive VLSI layout editor written in Cedar. It is normally used interactively, but all its operations can be accessed by other programs. In early design stages called Chipmonk II, ChipNDale is the Cedar successor to Chipmonk, an interactive layout editor written for the Alto world. But although ChipNDale looks a good deal like Chipmonk, there are quite distinct dissimilarities. Like Chipmonk, combinations of keyboard and mouse commands allow creation and modification of both primitive (contacts, transistors) and constructed (cells) objects. Multiple views of a design are available on both the color and B&W displays. ChipNDale can read in old Chipmonk files and some ChipNDale designs can be written out in Chipmonk format. Unlike Chipmonk, ChipNDale incorporates the concept of "technology independence", the idea that separate technologies (NMOS, CMOS, PC boards, etc.) do not interfere with the basic ChipNDale kernel, nor do they interfere with one another. New technologies may be created with their own definitions of commands and structures, allowing ChipNDale to expand to accommodate new methods and applications. There are three main sections to the ChipNDale documentation. The first is the user's manual, the file you are currently reading. The second is a guide to the additional tools that can be loaded along with ChipNDale; this document can be found in the file ChipNDaleTools.tioga. The third section is a set of hints for programmers of ChipNDale clients; this file can be found under ChipNDalePrograms.tioga. The rest of this introduction will provide you with step-by-step information to start ChipNDale and read in design files. The rest of the document is intended as a reference manual; use the "Levels" button to scan the document for the general section you are interested in reading. The amount of descriptive detail increases with the number of visible levels. The notes in small print at the deepest nested level are usually examples or explanations that the inexperienced user might need. The "Find" button can also be useful if you are searching for a particular topic. 1 The name ChipNDale comes from neither the fine furniture in England nor the fine figures in LA but from Chip 'n Dale, the two furry characters created by Walt Disney (two chipmunks -- Chipmonk II, get it? wrong!) Subnote: "Chip <-> Dale" also referred to the split between a technology independent kernel and all the add-ons, technologies and commands. 0.2. How to start Installing the program Bringover /DATools/DATools6.0/Top/CDDesign23.df It is usually best to create a separate subdirectory for ChipNDale; this allows you to remove it easily when you want to upgrade to a new version. This DF file will equip the machine with all the information it needs to run the NMOS, CMOS-A, CMOS-B, and ChipNSil versions of ChipNDale. The current version is called 2.3 and runs on top of Cedar 6.0. Start the program To start up a session of ChipNDale (in the same subdirectory containing its files) you can use the following load files: % CDCMosA or % CDNMos or % CDSil These load files will load the ChipNDale program and create a Terminal monitor viewer (hereafter referred to as "Terminal"). Terminal keeps a log of all the commands issued concerning ChipNDale; it is where you will look to find information about what ChipNDale is trying to execute and how that execution is progressing. Some technologies might have load files which make the start with commandfiles superfluous, however, using the commandfiles might be faster. When you use ChipNDale for the first time, just go ahead. Playing with ChipNDale is not dangerous: when ChipNDale reads in an existing design it will not overwrite the file unless you explicitly issue an output command. Then it asks you for a file name first, before doing any actual output. When you are an old Chipmonk user: ChipNDale is able to read in Chipmonk files; look in the documentation about additional tools. Get a design to work with To get an existing design up on the screen (after the program has been started) , use % CDOpen ChipNDale design files contain the technology of their design; However, the code handling that technology must be loaded before issuing the CDOpen command. If no filename was given to the read command, Terminal will respond with the request to type a file name in. The file may either be present locally or on one of the file servers; default extension is ".dale". You do not need to type in the extension. To start up a fresh design use one of the commands: % CDNewCMosA or % CDNewNMos or % CDNewSil or % CDOpen - These commands will display the design (or new viewer) on the screen. 1. General Definitions and Descriptions 1.1. The Terminal The Terminal viewer is one of the main communication points between the user and ChipNDale. Terminal not only keeps a log of commands executed but also prompts the user for input and displays error messages. There is only one Terminal for any invocation of ChipNDale, regardless of the number of designs displayed. 1.2. Technologies One of ChipNDale's main features is its ability to adapt to new technologies without changes to the core of the program. This feature is called "technology independence"; it means that new fabrication techniques or applications can be described in modules and plugged into the existing system. But this capability also means that the user must make sure that the appropriate technology is loaded so that ChipNDale can access features unique to that technology. For MOS designs, ChipNDale distinguishes between the NMOS and the CMOS technology. The "technology independence" of ChipNDale goes that far that even a technology ChipNSil is available, describing schematics or arbitrary drawings. 1.3. Design A design is what a designer creates; it is the unit used to be stored in files, and also the unit used in the synchronization. Every design is in a particular technology and consists of some geometry and a directory. The design is also the unit which is put into one file usually. 1.4. Objects Primitive objects are the "atoms", if you will, of the ChipNDale world. The existing primitives are transistors (straight and angle), contacts (buried and butting), and wires. Composite objects are cells, repetitions or imports. These are the building blocks of the more complex structures used to construct designs. All the composite objects must be listed in the design's directory. Cells are the most basic building blocks. The types of objects which can be included in a design are specified by the technology. However some types of objects, cells and rectangles, exist in all technologies. 1.5. Additional Tools ChipNDale makes it easy to write additional tools, causing a large variety of extra utilities to spring up around the core program. It is not possible to describe all additional tools in this document; you can find that description in ChipNDaleTools.tioga. The list of additional tools starts with "design rule checking", "making checkplots", "cif generation", "mask generation"... 1.6. Tip Tables Often used as the real truth of the user interface, users are invited to browse the tip table. The tiptable is alphabetically sorted and it has comments. ChipNDale typically uses two tiptables, one which describes the general ChipNDale user interface, and a second one which describes the technology dependent commands. 2. ChipNDale Viewer Commands 2.0. In General ChipNDale commands are grouped such that those most frequently applied use the lefthand side of the keyboard. This grouping allows easy finger placement without having to move your right hand away from the mouse. This speedy access, however, has outweighed mnemonics, which is why "Q" draws a transistor, not "T". Infrequently used commands have been shuffled off to the righthand side of the keyboard. Commands are executed in the ChipNDale viewer with the input focus. If the viewer does not have the input focus, the cursor will appear as a fat arrow pointing down. Click any mouse button to obtain the proper cursor. The mouse buttons are ordered such that the middle button controls drawing objects, the left and right buttons control modifications. Drawing only occurs when the middle button is pressed or held down; alterations only occur when the left or right button goes up. Most commands that affect selected objects can be performed with either the left or the right button, or with the CTRL key; the left button only affects the object pointed to, the right button or CTRL applies all currently selected objects. These commands are indicated in the documentation with the choice {Left or Right or CTRL}, meaning that the command will be applied to a different set of objects depending on the button used. The CTRL key can be applied only to execute those commands which do not depend on a mouse position. The following commands refer to the default CMOS and NMOS ChipNDale tip tables. All of the technology independent commands work also for ChipNSil; There are some paragraphs describing ChipNSil particularly. 2.1. The Pop-up menus and the control panel Pop up menus ChipNDale has real many commands, more than you are willing to remember. Pop up menus allow you to call commands, without having to know lots of exotic key combinations. There are many pop up menus available, and the menus can get additional entries when more programs are loaded. You can always try what commands a pop up menu has; mouse clicking outside of it discards the menu. To get a pop up menu, push the space key together with its letter key. - the global menu; mainly allows call of other menus - the text and properties menu - the cell menu; creation etc of cell - the directory menu; get an object, clean the directory... - the IO menu

- the program menu; call of additional programs. - the other program menu; call of additional programs. - the transformation menu; mirror and rotate - the names and properties menu - the viewer menu - the special commands menu - the generator setup menu - the draw mode menu - the imports menu <,>- the simplification menu <.>- the ticks menu - the grid menu Some few pop up menus are reserved for commands which need a position as parameter, these commands obviously need a mouse interaction to make the pop up menu appear.

- another program menu; programs executed on a rectangular area - another special commands menu; commands on a rectangular area - the hard copy menu; the called hard copy programs do all want a rectangular area as input parameter. - the generator call menu. Note: the pop-up menus can be altered dynamically by client modules while ChipNDale is already running; The general documentation can not accurately document all entries, but contains the most important entries . Control panel commands The control panel is a graphical method of changing layout parameters. Every design has a control panel associated with it; The control panel allows the designer to select default values, mainly the layer in which he wants to draw, but also some other modes. The panels also have some technology dependent entries. General Commands: Control panel commands are executed by clicking mouse buttons on top of the text (not the value). Left: increment value Right: decrement value CTRL Left: double value CTRL Right: half value Middle: (when done over a layer description) selects this layer as default for drawing wires - : shows a pop up menu, allows entry of arbitrary values. The control panel can also be scrolled. The 'split viewer' command allows the user to create a viewer on the associated design if all other viewers on that design have been destroyed. Technology dependent commands: There are several buttons on the panel referring to modifications to transistors. Both NMOS and CMOS panels have width and length buttons for changing the default measurements in the horizontal and vertical dimensions respectively. The NMOS panel has three additional buttons. The 'implant' button changes the type of transistor according to the following codes: NMOS transistor codes weak allows access to weak implants, a feature which you probably don't want to use. WEAK IMPLANT MEANING 0 0 enhancement 0 1 depletion load 1 0 threshold = 0 1 1 weak depletion The other two extra buttons change the width and length of pull-up transistors. 2.1. Simple Selection Select Single Object Left Point to desired object and hit the Left mouse button. All previous selections will be removed and this object will be selected. (Note: just the condition of being selected is removed, not the object itself!) Fine point: If the mouse position is exactly the same as before, and no other key is pressed, the selection will rotate through the possible objects at that point; otherwise the command will reselect the last selected object under the mouse position. This enables you to select objects completely obscured by other overlaying structures. Select Multiple Objects Right Selections made with the Right mouse button will be added to the collection of previously selected items. Deselect Object -Right Point to a selected object, hold down and hit Right. Selection will be removed. Fine point: -Left will deselect all objects. Change selection If you are selecting an object but have not yet let the mouse button up, you can change your choice by keeping the button down, moving the mouse to the new object and hitting . This change in midstream will also work even if you are about to execute a command on the selected object. For example: Say you want to rotate something. You press R, point to the appropriate object and press the Left mouse button. As soon as you let the button up, the command will be executed. But wait! You really wanted the object just to the right! No problem. Keep the mouse button and the R down, move the cursor to the new object, and hit . The selection will be switched to the new pointed objected. Now when the mouse button is released, the new object will be rotated (either in place of or in addition to the old object, depending upon whether the Left or Right mouse button was used). 2.2. More Advanced Selection <<***>> Area Select/Deselect There are two ways to handle area selections, the common area selection selects (or deselects) all objects which are completely included in a rectangular area. Use the common selection commands, but drag the mouse while the button is down. The other method of area selection handles every object which touches the designated area. -Left other area select --Left other area de select Select All - selects everything in the current design Select Entire Layer -{Right or Left} all of the objects belonging to the current layer will be selected or added to the selection. 2.3. Drawing objects Wires Middle Pressing the Middle button and moving the mouse draws a wire of the current layer with the current width, releasing the button confirms the position and length of the wire. Hitting while drawing a wire draws the first segment of the outlined wire. Hitting while drawing a wire flips the orientation of the direction the wire bends. Stops the wire drawing process. Note: The current layer can be changed with either the keyboard or the control panel, the width can be set only through the control panel. Note: When you statrted drawing a wire but think differently, press ESC to discard the outlined wire. Choosing a layer All the layer commands use keys in the top row. -Middle Clicking the middle button while holding down will set the current layer to be the same as the layer of a pointed object, if it has a unique layer. Change layer by hitting the associated layer number key. (CMos and NMos only). The control panel can also be used to change layers; note that the order of the layers associated with the keys is the same as the order listed in the control panel. CMOS <1> diffusion: default N+, with P+ <2> poly <3> metal <4> diffusion contact: default P+ to N-well, with N+ to P-well <5> N-well <6> 2nd layer metal In general, if the or key is down, everything is done in the P-diffusion world; up indicates N-diffusion. You can change between pdif and ndif just by switching the position of the key without hitting <1>. Note: NMOS uses <4> for 2nd layer metal, it has no wells or well contacts. ChipNSil layers are select with the control panel. Transistors (CMos and NMos only) Q-middle Draw a n-transistor (with SHIFT or LOCK: a p-transistor) W-middle Draw an angle n-transistor(with SHIFT or LOCK: an angle p-transistor) Contacts Contact commands use the same keyboard keys as the layer commands plus the middle mouse button; the contact is made between the indicated layer and metal. The command is executed by holding down the appropriate numeric keys while hitting the middle button. (CMos and NMos only). Middle mouse button while: <1> N+ to metal, with : P+ to metal <2> poly to metal <3> Butting P+ to poly and metal; with : N+ <4> P+ to substrate, with : N+ to N-well <6> metal to metal 2 <1>-<2> Buried N+ to poly; (There are no P+ buried contacts) <1>-<2>-<3> Butting P+ to poly and metal; with : N+ This command is supposed to remind you of the three layers used in a butting contact; everybody will probably use the simpler <3>-Middle command though. I know I would. Note: NMOS uses <4> for 2nd layer metal, therefore <4> for a metal to metal 2 contact; there are no substrate contacts. Drawing objects by name (from the directory) C-Middle Draw object, placing origin at current cursor position. Terminal will prompt for name of the object to be drawn. 2.4. Simple transformations Move by a vector -{Left or Right} Move selected object(s). If done with the right button, moves entire collection of selected objects relative to the former cursor position as indicated by the vector drawn on the screen when moving the mouse. The left button reselect a single object and moves only this object. Move an incremental step A-{Left or Right or CTRL} to the left. S-{Left or Right or CTRL} to the right W-{Left or Right or CTRL} up Z-{Left or Right or CTRL} down Note that the four keys A S W and Z are arranged in the same relative positions as the directions they move the selected object(s). The size of the step can be set by the control panel. Copy -{Left or Right} Copy selected objects positioned according to the drawn vector; the simple copy is similar to a move save for an additional -- however, the step moves do not have a corresponding copy version; they would not make sense. If done with the right button, copies entire collection of selected objects by choosing an origin with the left mouse button, holding that button down, and moving the cursor to the desired destination. The left button only copies the single selected object. Rotate and mirror R-{Left or Right or CTRL} Rotate selected object(s) by 90o in a clockwise direction, the bottom left corner remains fixed. T-{Left or Right or CTRL} Mirror selected object(s) across the vertical axis E-{Left or Right or CTRL} Mirror selected object(s) across the horizontal axis Note that rotation and mirroring can also be done with the Transform pop-up menu, -T. Rotation is the R command; for mirroring E and T were selected because they are located next to the "R" (rotate) key and have symmetries appropriate to their function. Delete D-{Left or Right or CTRL} Delete selected object(s) Un-Delete D-ESC Undelete last deleted object(s). Undelete may be repeated some times. 2.5. Stretching objects Stretch {A, S, W, Z or none}--{Left or Right} Note that stretching is very similar to the moves; instead of moving the object, only the pointed border is moved, the object is stretched. Therefore, the stretch commands are identical to the move commands except, that a modifier key, is used. The letter A, S, W, Z or Q specify the direction and the amount, as in the moves. You must be pointing to an edge of a selected object each time the mouse button is pushed. The pointed edge will be stretched. For now, angle transistors stretch in a crazy way, please be forgiving. 2.6. Some exotic but useful or necessary commands <<***>> Stretchy move {--A, S, W, Z} {-}-{Left or Right} Stretchy move is a special move which maintaining primitive connectivity; The commands are like the moves, except the TAB modifier key. Stretchy move is implemented in a strictly geometric way and does not understand the electrical behavior... be gentle on imperfection. Measuring distance, counting objects, information about an object -Middle -- Click the middle key quick when is down: you get information about the selected objects. -- Draw a vector by holding down and the middle button while moving the mouse. When the mouse button is released, Terminal will display the values of the end coordinates and the distance between them. Yes, these two commands use the same keys, only the time scale is different. Split a wire |-{Left or Right} Split wire(s) along its/their width by holding down both the "|" key and the appropriate button while moving the mouse. Command is executed by lifting the mouse button. Move to grid /-{Left or Right or CTRL} Move object(s) to a grid position Did you notice that / is the general grid key?. Grow by width G-{Left or Right or CTRL} Grow wires in length direction by the amount of their width. This is handy to draw boxes when working with a coarse grid. To shrink back to grid positions use the split command and delete the small piece; I do nto believe that you really want to shrink to other than grid positions. Interrupt the drawing - Hold down a few seconds! Interrupts the drawing, of all viewers, immediately after the command is accepted Abort a command - Aborts the current command; works at least if the implementation of the current command is kosher and asks for the abort flag... . Of course, short commands do not ask the flag, but the abort command at least flushes the command queue. An analogue is using to abort an input on Terminal. Special commands menu -S The special commands menu is a catch-all menu for odd commands which don't really fit in elsewhere. It includes commands such as undelete, abort command, and statistics, among others. -S The special commands menu with commands which depend on particular position or area. It contains comands for setting or defaulting the interest rect of the pushed in cell. Debug command <^>-middle Enter the debugger. Shows first a pop up menu to decide whether the locking of the design should be released. It is conveniant to release the lock, this allows to issue other commands while the debugger still has a handle into the design. However, if the lock is released the debugging actions are not queued properly and it is up to the designer to prevent any problems due to concurrency. The debugger is called from a procedure which allows you to inspect easily the selected object, it's specificRef field, the instance, the design or th command. A special procedure Include may be called from the interpreter. This procedure includes any object or instance into the design. It is up to the user to make sure an included thing is correct. It is perfectly save to either abort or proceed a debugger created with the debug command. Arrow command -middle Puts down an arrow at this position. (Some commands might depend on the position pointed to by this arrow.) Don't rely on the arrow position over multiple commands, some commands might move the arrow position implicitely. Remove the arrow 2.7. Viewer commands Change scale "<", ">" Hitting <<> increases magnification; hitting <>> decreases it. It is easier to remember these commands by looking at the upper case options on the keys, but of course the real keys are <.> and <,>. Or, if you want to be visual in remembering the commands, note that the "<" starts small then gets bigger, hence it makes objects appear bigger. In the same way, ">" starts big and ends small, making objects appear smaller. Interrupt drawing Hold down for about 2 seconds. Will interrupt the drawing on all ChipNDale viewers. This command is usefull to interrupt the drawing if a complex design is drawn in excessive detail, which might need hours... The drawing can be repeated simply by zooming or paning. Change position, pan viewer -Middle Moving the mouse while holding down both the key and the middle button draws a vector on the screen. The view of the design will be moved in proportion to that vector when the mouse button is released. Show a particular area, zoom in viewer -Left --Left Drag a box to define an area. The view of the design will be scaled and moved such that this box will be displayed. This displays the drawn area on the viewer; together with SHIFT it choses another viewer. -Left (not with !) can be un-done with . Show position of other viewers <<***>> -Middle Shows the positions of the other viewers. View top cell <<***>> - Cause the viewer position and scale to change so that all objects of the top pushed cell are visible on the screen. View all selections <<***>>  Cause the viewer position and scale to change so that all selected objects are visible on the screen. Changing the simplification treshold Use the simplification menu either directly or through the viewer menu. The simplification treshold can also be changed on a per cell base (The actual treshold value is a product from the viewer and the cell treshold value). See the cell menu for this command. 2.8. Cells Note that these commands can also be accessed through the cell pop-up menu, -C. Drawing cells is not a special command but like putting down any named object which is in the directory: use the C-Middle command. Create cell X-C-Middle Create a new cell from the set of all selected objects. Terminal will prompt for a unique cell name. This double key command is easy to remember: X is just the neighbour key to C, which is used for all cell related commands. Expand (Flatten) cell Use the cell pop up menu. (C-Space) Push-Pop C-{Left or Right or CTRL} Push into cell: the rest of the design will be grayed. C- Pop out of cell The push command may be executed for certain other object classes than cells. A pop up menu will ask whether and how the object should be transformed into a cell. Select whether all instances of this object should be transformed to an aequivalent cell, only this instance should be transformed or skip the command. Interest rect The interest rect denotes the interesting area of an object. It has been defined to denote an artificial cell boundary for routers and module generators. The interest rect can be defaulted or set to any particular value. (Use the "special commands with rectangle" menu; S- ). The interest rect should not point outside the area where ChipNDale is drawing. Even if except drawing all else works correctly, this is condidered erronous usage of ChipNDale. Directory -D Directory pop-up menu: list subset dir: list explicitely named objects list complete dir: list complete contents of directory prune subset dir: list unused entries created by programs, and ask whether they should be removed from the directory. (Convention: The first character of an object name determines whether it is considered created by program; programs use non alphanumeric character as first letter) prune complete dir: list all unused entries, and ask whether they should be removed from the directory. remove ob from dir: remove a particular entry from directory, (checked, only unused entries can be removed) replace ob: replace a perticular object in the whole design list imports: list names of imported designs list importee's ob: list referenced object of a particular imported design CELLS: calls Cells pop-up menu Although the directory contains mostly cells, there are other object classes stored there as well. Cell pop up menu -C Cell pop-up menu: create: see create cell expand: Expands (flattens) the selected cell. push in: see push-pop. pop out: see push-pop. simplification: set the simplification treshold for this cell transform to: transforms the selected object into a cell. Works only for composite object classes. push named: Requests a name. Push into any instance of of the named cell. DIRECTORY: shows directory pop up menu. 2.9. IO, Imports, and Includes IO The IO menu allows operations on designs which already have a viewer; use the CommandTool commands to read in the files originally. -I Use the IO pop-up menu. Default extension is .dale. save: Stores design using same file as for input. If the design was not created by reading in a local file it ask for a file name. output: Requests filename and stores the design. load import: Requests filename and loads this design ready for doing imports. Whereas you type a FILE name for this command, it imports a design with DESIGN name as found on the file. include: Requests filename, loads this design and completely include it into the design used for the command. load all imports: Tries to load all imported files. Uses design name as default for filename; It is possible to specify other filenames using the user profile. Chipmonk files: How to read or write Chipmonk compatible files is described in the documentation ChipNDaleTools.tioga. If the Chipmonk compatibility program is started it will register further commands into the IO menu. Imports and Includes Include: Take some objects from some other design and copy them in. The copied objects are completely a part of the target design. Import: To import a design means to make references to objects from the imported design (the library). The imported objects are not included in the importing design but only referenced. If objects are changed in the imported design (the library), and this design then re-loaded, the changes made are propagated to our importing design. To really see imported objects it is necessary to load the design they are imported from. Think an imported design is a separate module. Objects are procedures. The size of the object corresponds to the Type of the procedure. Having an imported design not loaded corresponds to an unbound procedure... -X Use the imports pop-up menu. load import: Requests filename and loads this design ready for doing imports. Whereas you type a FILE name for this command, it imports a design with DESIGN name as found on the file. list imports: list the imported designs. list importee's ob: list referenced object of a particular imported design merge in imports: Request an imported DESIGN name. All the imported objects from this design will be copyed and completely included into the design used for the command. include: Requests filename, loads this design and completely include it into the design used for the command. load all imports: Tries to load all imported files. Uses design name as default for filename; It is possible to specify other filenames using the user profile. replace included by imports: Ask for a design name. Tries to find all objects which came from this design and replaces those objects with imports. select DESIGN: Use this design as future source of inter-design operations. Simple, but verbose method to create imported object. X-Middle Draw an imported object. The command queries for the design, and then for the object. A reference to this object is drawn. If the design has not been loaded yet, it asks whether it should. More easy way to draw imports: Open a viewer on the design which is used as source; make this design is the selected design (X-Z-Left). Select an object in the source design. To draw this object in your design, use X-Z-Middle. This double key command is easy to remember: Z is just the neighbour key to X, which is used for all import related commands. X-Z-Left Use this design as future source of inter-design operations. (this means we remember this design as selected design; it does not mean that its objects are selected) X-Z-Middle Makes and draws an reference to the selected object in the selected design. (Only one object must be selected in the selected design) To make confusion complete, there is a third way to draw imported or included objects: Use generators. Once a reference to an imported object is made, it is possible to really include that object in the current cell directory. It is then no longer referenced but a part of the new design: use the "merge in" entry in the pop up menu. It is even possible to undo a merge-in (The "replace included by imports" pop up menu command). However any editing on merged-in objects makes them forget whether and where from they were included. 2.10. Repetitions Description A repetition is a set of objects placed at regular intervals along a given vector a given number of times. This feature allows the designer to create uniform structures quickly and easily. Any group of objects can be used as the basis for a repetition, even repetitions themselves. Commands =-Middle (note the repeated horizontal lines) Make a repetition of the selected objects Select the objects you want to form the basic unit of the repetition. Hold down "=" and draw a vector with the middle button. The vector indicates the spacing of the units. The vector is pointing to the position of the origin of the next unit, where the origin of any unit is defined by the tail of the vector. After the middle button is lifted, Terminal will prompt for the number of units you want in the repetition. [-{Left or Right} Increment count on selected objects (repetitions) ]-{Left or Right} (note that "[" and"]" are just below "=") Decrement count on selected objects (repetitions) =--Middle Change the repetition vector of the selected repetition. Any repeated object has the possibility to ask what index it has in the repetition. It is possible to change a repeated object into a cell; however there is no way back. 2.11. Properties, Signal Names It is possible to hang arbitrary properties to any instance of any objects. These properties may or may not affect any program's behavior, or may only be comments for designers. Programs can protect their properties from designers, so the property mechanism can be used without danger of contention. SignalNames are reserved properties "$SignalName". Their value should be a ROPE. InstanceNames are reserved properties "$InstanceName". Their value should be a ROPE. -N The names and properties menu. [The letter P is reserved for Programs, not properties.] Shortcuts: N-Left Shows all the properties and values of the selected instance on terminal. N-Middle Enter signal name for the selected instance. N-Right Display signal names of all visible instances in the viewer. The Name and Properties Menu -N Name pop-up menu: Property (design): put a property on the design Property (instance): put a property on an instance (Application) Property (object): put a property on an object; this is only possible for objects which are contained in a designs directory Comment (design): look or put a coment on a design. Comment (instance): look or put a comment on an instance (Application). Comment (object): look or put a comment on an object; this is only possible for objects which are contained in a designs directory. Rename design: rename the design Instance-name: put an instance name on the selected application Rename Object: rename selected object in directory Signal-name: put an signal name on the selected application; this can have side effects if application is not using a rectangle. Show prop (design): Show the properties of the design. Show prop (i&o): Show the properties of the selected objects and applications. Display signal-names: Display signal names of top layer cell. To put a property on something: Answer the question for the property name and wethter to replace the value of the property. Properties included interactively cannot make use of all the nice Cedar types, however, a pop-up menu allows you to select the types of the property value in some limited range. Preferred types for properties are Rope.ROPE, ATOM and REF INT. The name of a property is always converted to an ATOM. Properties using these types are saved while a design is written on a file and read back. However, clientprograms may affect this and force a different behavior for properties they own. Such properties are usually reserved by the implementor for his/her exclusive use so designers will not be surprised. It may be good to load client programs first, and only thereafter use undocumented properties; they might be disabled by a client program, even if it runs later. 2.12. Text in ChipNSil T-middle Q-middle Draw a text in the current font. The font selection is made using the control panel. The available fonts in the control panel are set up with the userprofile. Changing the userprofile changes the available fonts immediately. The user profile helps for creation of text only. Once a text is in a design, it will not change font on user profile changes. Q-{Left or Right or CTRL} Edit the selected text. F-{Left or Right or CTRL} Change the font of the selected text. (Use current selected font with the control panel) 2.13. Generators U-space Generator environment setup menu. Certain set up commands for different generator environments. Allows flushing the cache of a generator (make it forget an object has been already created) U-middle Calls a generator of the current generator environment (context). Depending of the selected generator context a generator is select using a pop up menu, by typing its name or by a generator context specific method. The selected generator is called and the generated object included at the mouse position of the command. The current generator environment (context) can be selected using the control panel. Generator contexts are specified with a name. Typically a new name is used for any particular project. Some names are used by certain tools. Normal user defined generator contexts have only a name to destinguish their identity. They cause selection of a generator using a pop up menu. The following tool generators are predeclared DIRECTORY: Reads a name from terminal and fetches the object from the directory INCLUDE: Reads a name as designName.objectName from terminal; the object is transfered into the design where the command was issued and included. If necessary the design designName is loaded first. The design is assumed to be found on file with name designName. IMPORT: Reads a name as designName.objectName from terminal; the object is imported into the design where the command was issued and included. If necessary the design designName is loaded and imported first. The design is assumed to be found on file with name designName. See ... for how to write generators. 2.14. Using the Color Display ChipNDale also uses the color screen as a viewer. ChipNDale's colors are set up different than the standard Cedar colors, but it does not behave as if it owns the color device; it uses whatever color display settings it finds. To set up pleasent colors for ChipNDale, the color map must be set explicitely. You might use the "8-bit-color" button to select which colors you want to install, or load a particular color map file using the command ColorMap filename in a command tool. How colors are set up internaly: Patterns and Maps To make reasonable use of the color commands, you have to understand how the colors are generated. Colors are generated in two steps, each of which can be set up separately. Only well matching combinations of these two steps can make reasonable colors. In a first step a layer causes a certain pattern of pixel values to be or-ed into a bitmap. This pattern may contain several pixels, each of several bits. In a second step each pixel in the bitmap is mapped through a color map to cause an actual color to appear on the screen. Generating the pixels can in principle be personalized on a per viewer basis. On normal usage, each technology specifies how its layers are mapped into pixels. The color map however, is part of the display hardware. Only one color map can be active at any time. Interactive color tools A interactive color tools exist (for cmos and nmos only) which allow changing of colors. See the documentation of additional tools for how to use it. 2.15. Polygons <->-middle Polygons are not first class citizens of ChipNDale. Prior to using Polygons make sure that all the tools necessary understand them. Right now: CIF generation and ploting understands Polygons, but mask generation, DRC and extraction does not. All the Polygons work with "-"-middle. A pop up menu allows selection of the actual command. To create a polygon select draw polygon in the pop up menu. A triangle will be drawn, one point is where the mousebutton was pushed down, the second where the mousebutton was released; the third point is arbitrary. Edit the triangle to get the desired polygon. The pop up menu shows further entries to add a point to the selected polygon, to remove a point or to move a point. 2.16. Pins ;-middle Draws a pin on the current layer. You are supposed to give the pin a name. Pins are a mean to give rectangular areas names. Pins further have an owner and a layer. The owner means which program specifies the semantic meaning of the specified area. Interactive drawn pins have a nil owner. There are no layer or name restrictions on pins. Pins are the general scheme with which name-area asssociations can be made for ANY program. Multiple pins may well have the same names. ;- Changes the layer of a pin to the current layer. 2.17. Alignment marks Y-middle Draws an alignment mark. Alignment marks are a mean to give names to points. There are no name restrictions on Alignment marks. Alignment marks are the general scheme with which name-point asssociations can be made for ANY program. Multiple alignment marks may well have the same names. 2.17. Useful Things to Know The ESC key: Works mostly as an UN-key Stops drawing wires or any other cursor tracking command. Works as De- select on all the select commands Undelete with D. Is involved in both, the stop-draw and the stop-command commands But: It is also in the same row than the layer keys! ESC-middle picks up a layer. If output of a design crashes but you want to save it Look at ///ChipNDale/temp/...... Did you try SHIFT-SHIFT-SWAT? (hold it down for a couple of seconds). 3. ComandTool commands Note that capitalization is not significant when giving the commands 3.0 Loading the program CDNMos, CDCMosA, CDSil 3.1 Creating new viewers CDNewNMos, CDNewCMosA, CDNewSil Create a new empty design in the appropriate technology. 3.2 Reading in designs CDRead {optional filename | (-technology name)} CDOpen {optional filename | (-technology name)} Read a ChipNDale design. (.dale file) The technology of the design on the file must be loaded. If the filename is not specified, ChipNDale will query for one. 3.3 Calling generators CDGenerate generator {out|*} _ {in|-technology} generator: generator to be called; Uses a generator environment specified by the input design; The generator environment defaults to "USER". out: file name for the output design "*" for out: create viewer for output design in: file name for the input design "-technology" for in: new design of technology "technology" will be created 3.4 Color Settings ColorMap {-n} {optional filename} Reads and installs a color map file. -n causes the the file to be installed only if the color display is already on and in 8 bit mode. OutputColorMap filename Creates a color map file using the current color map. (You need special tools to set up the the color map first...) 4. User Profile Options It is usually good to specify full path names for filenames mentioned in the user profile; user profile readings are processed with different working directories. The user profile options are shown here with their default values. WARNING: When ChipNDale is started a reasonable working directory is assumed. When the user profile is edited, NO working directory is assumed. 4.1. Control of the pop-up menu PopUpMenu.FontFamily: "Helvetica" PopUpMenu.FontSize: 10 PopUpMenu.FontBold: TRUE PopUpMenu.FontItalic: FALSE PopUpMenu.LineHeightChange: 0 4.2. ChipNDale kernel ChipNDale.FirstViewerOnColor: TRUE ChipNDale.ControlViewerOpenIconic: FALSE ChipNDale.TerminalStartRight: TRUE ColorDisplay.Side: Left ChipNDale.RunPrograms: NIL Imports ChipNDale.ImportFor.DesignName: "FileName" Debugging ChipNDale.CatchLowLevelErrors: TRUE ChipNDale.CatchErrorsWhichCauseDeadlock: TRUE 4.3. Technology-specific user profile options ChipNDale.ChipNSil.TIP: Default ChipNDale.NMos.TIP: Default ChipNDale.CMos.TIP: Default ChipNDale.CMosB.TIP: Default 4.4. Font user profile options Not all technologies support setting up fonts from the user profile. ChipNSil and CMosB do. The technology name is part of the user profile option. ChipNDale.ChipNSil.Font0: "Xerox/TiogaFonts/Helvetica10" ChipNDale.ChipNSil.Font1: "Xerox/TiogaFonts/Helvetica7" ChipNDale.ChipNSil.Font2: "Xerox/TiogaFonts/Gates32" ChipNDale.ChipNSil.Font3: 20 "Xerox/PressFonts/Helvetica-bir" ... ChipNDale.ChipNSil.Font19: "Xerox/TiogaFonts/Symbol64" ChipNDale.CMosB.Font0: 4 "Xerox/TiogaFonts/Helvetica10" The control panel font module supports 20 fonts (per technology); which are initialized with the user profile. The user profile designates the font used on creation of the text; once a text is created, its font does not depend on the user profile contents any more. Fonts may be scaled; defaulting the scale results in a scale of lambda, what is the right scale for TiogaFonts. (The unit for the scale value is not "lambda" but the smalles number representable in the technology) Try what the difference between TiogaFonts and PressFonts looks like. 5. The Outside World 5.1. Necessary system Dorado with Cedar 6.0; If you need ChipNDale desparately a DandeTiger might do... 5.2. DF files "c" stands for the current ChipNDale version number, right now 23 (meaning 2.3) but the zero is seldom written. "cc" stands for the Cedar release used for the ChipNDale version, (for ChipNDale 2.3 use 6.0, since ChipNDale 2.3 is programmed in Cedar 6.0. DF files for designers /DATools/DAToolscc/Top/CDDesignc.df /DATools/DAToolscc/Top/FooToolc.df where FooTool is the actual tool It might be good to create a separate subdirectory for ChipNDale; this allows you to remove it easily when you want to upgrade to a new version. You should run ChipNDale from the same subdirectory where you store it, so you get the correct default fonts, icons, colortables... (ChipNDale does not use servers as a default because they might be down.) DF files for programmers /DATools/DAToolscc/Top/CDCommonc.df /DATools/DAToolscc/Top/CDCMosc.df /DATools/DAToolscc/Top/CDNMosc.df /DATools/DAToolscc/Top/ChipNSilc.df DF files for documentation shared by different tools /DATools/DAToolscc/Top/CDDocc.df Contains documentations how to use some further basic ChipNDale related tools and how to program extensions to ChipNDale. Other ChipNDale related tools have their documentation directly in their df file. 5.3. Distribution-lists on the Grapevine ChipNDaleImplementors^.pa The pure creatures reading your complaints, uh, suggestions; actually we really like to get suggestions. Unhappily it happened far more often that valuable suggestions were not made then that nonsense complaints made me. ChipNDaleUsers^.pa The user society. You get release messages, status reports and thereon. If you use ChipNDale for doing VLSI you probably should also be member of DAToolsUsers^.pa. ChipNDaleDiscussion^.pa Open forum for discussion. This list will also get all messages sent to ChipNDaleUsers^.pa and some more. DAToolsUsers^.pa The general design tool user society. You can avoid beeing a member in this list if you use ChipNDale only as an illustrator. DAToolsImplementors^.pa Like ChipNDaleImplementors^.pa, but also for non ChipNDale related tools. Note: Lists are restricted to Xerox employees, part-time employes and PARC summer students. 6. ChipNSil ChipNSil is really exactly like ChipNDale! You don't have to learn any new command except the commands to draw text or exchange fonts. (See in chapter 2.12. "Text in ChipnSil"). How to get Fonts You should get the Cedar fonts on a full boot. Do never use fonts which are not placed in the standard directory for fonts; When you read the design in later, a private font may no more be there and would be substituted. ChipNSil remembers fonts by using its name. A font, eg. Xerox/TiogaFonts/Helvetica8I is searched using a full path name ///Fonts/Xerox/TiogaFonts/Helvetica8I.ks ... Hint on macro design, to make it easy accessible: To create macros(=cells) be carefull to make connection points on grid points. Use a grid of 4 for real design, but a grid of 1 while designing a macro. All connection points in a macro should be 1 lambda squares of black which sits on top of a 4 lambda grid point. Make an interestrect to the macro such that the lower left corner sits on a 4 lambda grid point. The size of the interrestrect should then be either a multiple of 4 lambda or a multiple of 4 lambda + 1. 4-- opens ChipNDale viewers on the color screen directly, if screen is empty -- controls creation of control panel viewers -- moves the Terminal viewer to the right --or Right; this user profile option is shared with the ColorDisplay tool. -- include a list of bcds which should be run whenever -- ChipNDale is started. (These programs are started before a technology is initialized). -- whenever the command "import all" is called, an import of design DesignName -- will cause the file FileName to be loaded. DesignName any identifier. -- DANGEROUS, better don't set to FALSE -- set to FALSE to help debugging, usually it is possible to continue -- DANGEROUS, better don't set to FALSE -- set carefully FALSE to help debugging, but -- if errors occur, you loose all your work which is not saved onto files -- Tip tables can be layered, like for Tioga; -- Default extends to -- /indigo/ChipNDale/@/#%/ChipNDale#.TIP /indigo/ChipNDale/@/cd%/ChipNDale.TIP -- where @ is the Cedar version number, # the ChipNDale technology, % the ChipNDale release number. -- Fonts Êú– "cedar" style˜Iblock•Mark centerHeaderšÏs ˜ K– centerFooterš˜Ititlešœ ˜ Isubtitle˜&M˜M˜ Iauthorsšœ*˜*Iabstractš6˜6OšÐms>ž˜@OšÏb œ°˜¹O˜I boilerplateš ÏqœÏoœ¡œ¡œ¡Ñbox˜Žhead1˜J˜J˜'J˜Jšœ˜Jšœ˜J˜Jšœ ˜ Ibody˜Jšœ=˜=RšŸœx˜‡RšŸœÛ˜ïRšŸœÏ˜æRšŸ œ˜RšŸœr˜ŽRšŸœ3˜JR˜— šœ¤˜¤RšŸœ˜/—R˜ ˜head˜ Ršœ Ðsuœ¡˜«Ršœê˜êRšœ˜˜˜RšœÀ˜ÀR˜InotešÏlœä˜å— šœ˜ šœ˜Sšœ0˜0Ršœß˜ß— šœ˜ šœx˜xSšŸœ Ÿœ Ÿœ˜"—Sšœý˜ý— šœ˜ šœU˜USšŸœ3˜5Sšœ™˜™— šœ3˜3SšŸœŸœ Ÿœq˜’———— ˜' ˜Ršœ¼˜¼— ˜Ršœº˜º— ˜ R˜š— ˜ Ršœ²˜²R˜ýR˜§— ˜Ršœÿ˜ÿ— ˜RšœÁ˜Á—I pagebreak˜— ˜ ˜Ršœô˜ôR˜ŠR˜–RšœÓ˜Ó— ˜+ ˜ KšœÊ˜ÊItable3šŸ œ3˜>VšŸ œ˜)VšŸ œ$˜0VšŸ œ:˜FVšŸ œ ˜VšŸ œ/˜:VšŸ œ5˜@VšŸ œ+˜6VšŸ œ˜)VšŸ œ˜VšŸ œŸ˜&VšŸ œŸ˜%VšŸ œŸ˜VšŸ œŸ˜VšŸ œŸ˜%VšŸ œŸ˜VšŸ œ Ÿ˜V˜Všœ¥˜¥VšŸ œ>˜KVšŸ œ>˜JVšŸ œgŸ˜uVšŸ œŸ˜&V˜TšœÔ˜Ô— šœ˜K˜ÀSšÏzœ˜Kšœa˜aJ˜VšŸœ˜VšŸœ˜VšŸ œ˜VšŸ œ˜VšŸœ-˜5VšœK˜KVšŸ˜VšœŸ œB˜N—J˜¹˜Sš¥œ˜šœí˜íšÐbz˜J˜—JšœU˜UJšÐfz˜˜Jš¤œ¤œ˜Jš¤œ¤œ˜J˜Jš¤œ¤œ˜Jš¤œ¤œ˜——J˜J˜QS˜—— ˜S˜itemšŸœØ˜ÜTšœÒ˜Ò—S˜WšŸœk˜pS˜šŸ œY˜dTšœ1˜1—S˜šŸœ¨˜¯T˜Ý——head2˜%S˜Wšœð˜ðWšœZ˜ZWšŸ œ˜ WšŸœ˜.Sšœ ˜ WšŸœ+˜:S˜WšŸœa˜u— ˜S˜WšŸœ¯˜µWšŸœU˜\WšŸœ^˜eWšŸœ"˜'˜T˜ŠT˜e—W˜S˜W˜1šŸ œœ˜¨W˜K˜ôJ˜Jšœ˜šŸœ˜Jšœ˜—JšŸœ˜ JšŸœ˜ šŸœ˜Jšœ1˜1—JšŸœ ˜ šŸœÏuœ ˜J˜—Kšœë˜ëIdefault˜Kšœ¨œ/˜JK˜3—S˜ Wšœ˜WšŸœŸœŸœ˜EWšŸœ#ŸœŸœ˜P ˜Kšœ˜˜˜J˜Jšœ˜Wšœ-˜-Wšœ˜Wšœ5˜5Wšœ2˜2Wšœ˜W˜Wšœ@˜@šœ>˜>T˜¨—˜Kšœ¨œ\˜w—J˜—S˜,WšŸœt˜|— ˜S˜šŸœ˜3T˜ý—S˜WšŸœ˜(WšŸœ˜(WšŸœ˜šŸœ˜ Y˜K˜ºY˜—Sšœ˜šŸœä˜ûT˜‚—Sšœ˜WšŸœ"Ðmuœ@˜|WšŸœ5˜NšŸœ7˜PY˜K˜\K˜§Y˜—S˜šŸœ˜5J˜—Sšœ ˜ WšŸœI˜N— ˜Ihead3šœ˜šŸ*œÓ˜ýTšœ˜TšœI˜I—— ˜:S˜ WšŸœ˜WšŸœ˜!šœ‰˜‰Kšœ†˜†— ˜AšŸ ˜ W˜cW˜Ð˜K˜L———S˜ WšŸœ®Ÿ˜ÂZšœ Ÿ˜ šŸœ$˜=TšœŸœ˜1—Zšœ Ÿ˜šŸœ?˜XTšœß˜ß—W˜S˜WšŸ œn˜xS˜šŸ œï˜úW˜J˜9— ˜WšŸ œ»˜ÅWšŸ œ­˜¸— ˜ WšŸ œ‹˜–W˜ãW˜Z— ˜ WšŸ œà˜ëWšŸœ˜—— ˜S˜ šŸœ Ÿœ%Ÿœ—˜ÒT˜à—S˜WšŸœ˜˜S˜WšŸœÕ˜ãS˜'WšŸ œ˜WšŸœÓ˜çTšœB˜BS˜(WšŸ œ,˜6S˜WšŸ œv˜ƒS˜WšŸœh˜vS˜$—WšœL˜LT˜½ ˜ IindentšœÉŸœ ˜ÚS˜ šŸ œh˜rKš{˜{W˜—S˜Wšœ$˜$S˜WšŸœ9˜RšŸ œ˜Wšœ¼˜¼—W˜S˜ Wšœ‘Ïi œ·˜ÒW˜ šœ ˜ JšŸ ˜ ˜Jšœ˜WšŸœ!˜0WšŸœ(˜9WšŸœ˜WšŸœU˜gWšŸœY˜kWšŸ œ3˜=WšŸ œ"˜.WšŸœ9˜KWšŸœ˜! šœc˜cW˜——— ˜JšŸ ˜ ˜Jšœ˜WšŸœ˜WšŸœ'˜-WšŸœ˜WšŸœ˜WšŸœ1˜?WšŸ œY˜eWšŸœ?˜MWšŸ œ ˜)——— ˜ šœ˜R˜ƒR˜šŸ ˜ Ršœ6˜6WšŸœ˜ƒWšŸœ*˜0WšŸ œ­˜¸WšŸœf˜mWšŸœ‘˜¡W˜JšœÜ˜Ü—— šœ˜SšŸœ|˜ƒKšŸœ©˜¯KšÖ˜ÖS˜—šŸ ˜ Ršœ ˜ WšŸ œ­˜¸WšŸ œ˜(WšŸœ8˜JWšŸœš˜ªWšŸœf˜mWšŸœ‘˜¡WšŸœx˜“WšŸ œ>˜KW˜J˜—K˜7W˜WšŸ œÁ˜Ê˜çKš}˜}—W˜WšŸœ¥˜­W˜šŸ œ˜ K˜†——K˜hK˜Kšœ¯˜¯K˜S˜ ˜ ˜ K˜ž— ˜šŸ œ$˜/˜)T˜¦T˜——šŸ˜W˜1—šŸœ ŸœŸœ˜