[_CDCSL_93-16_]<1>Cedar>release>CedarRelease>IIFC10i.tioga~

InstallationInstructionsForCedar10i.tioga

Willie-sue Orr, October 21, 1992 3:49 pm PDT

InstallationInstructionsForCedar10i

CEDAR 10.1 % FOR INTERNAL XEROX USE ONLY

InstallationInstructionsForCedar10i

Created by: Nan Stumbo:Roch803:Xerox and extended by Willie Sue Orr:Parc:Xerox.

Maintained by: Willie Sue Orr:Parc:Xerox

XEROX Xerox Corporation
Palo Alto Research Center
3333 Coyote Hill Road
Palo Alto, California 94304

For Internal Xerox Use Only

1. Introduction

This document describes the procedure for installing Cedar10.1 and Printing10.1 on a Sun file server. It is assumed that the site is already running PCedar2.0.

2. Requirements

The following is a list of requirements for adding Cedar10.1 and Printing10.1.

8mm Video Tape Drive

Cedar10.1 and Printing10.1 require an additional 500Mb (Cedar10.1 is still growing so be warned):

/Cedar10.1 ~448Mb

/Printing10.1 ~37Mb

/xrhome ~21Mb (for 4𡤄.X)

/project/imagerfonts ~72Mb

3. Release Tape

The Cedar 10.1 Initial Release Tape contains the following directories:

xrhome/R←V.X (R←V - the current Release←Version number, i.e. 2�.X or 3𡤀.X)

cedar10.1

/project/imagerfonts/xerox

(printing10.1)

There are two copies of the four (three if no printing10.1) on the tape; see accompanying listing with the tape.

The xrhome/R←V.X directory is the PCR code. /project/imagerfonts/xerox contains the fonts. The Cedar code/tools are in cedar10.1/release. Other useful unix tools are in cedar10.1/bin.

For a list of the contents of each of these directories see Appendix A.

A. Reading the tape

Reading the tape will take 1-2 hours (it took 30 minute to write one copy of the files).

NOTE: Due to the way the tape must be written it is necessary to first create the directories /fsrvr/project/imagerfonts, and then change directory to it before reading this part of the tape. The problem is that the path names in the imagerfonts subdirectory get longer than tar will accept.

# cd /fsrvr

# tar xvf /dev/nrst1 (extract directory xrhome/R←V.x)

# tar xvf /dev/nrst1 (extract directory cedar10.1)

# mkdir project

# mkdir project/imagerfonts

# cd project/imagerfonts

# tar xvf /dev/nrst1 (extract directory /project/imagerfonts/xerox)

# cd /fsrvr

# tar xvf /dev/nrst1 (extract directory printing10.1 if present)

# mt -f /dev/nrst1 rewind (rewind the tape)

4. Setting up the Files on the File Server

There are a couple of modifications which need to be done to the files on the file server so that they are available to all workstations which will be running Cedar. The following sections describe these changes.

A. Establishing Links on the File Server

A link for the INSTALLED version of PCR needs to be established.

WARNING: Be very careful with the ln command. It will NOT give you an error message if the target directory/file does not exist!

# cd /fsrvr/xrhome

# ln -s R←V.x INSTALLED (where R←V.x is the latest release of PCR)

5. Installing Cedar on a Workstation

There are two ways to set up (most of) the environment that the wordstation needs, to be able to run Cedar. If you have the Sun Yellow Pages running and are willing to create new automount maps, that is the easiest, especially if you have more than a couple machines. Otherwise, you need to install links on each of the machines.

YP maps

Cedar makes use of two yp maps. One, called project, needs only the entry cedar10.1 (for Cedar's use). The second, called pseudo, needs to have an entry for xrhome. These entries need to reference to appropriate directories on your fileserver(s).

Cedar10.1 does not use the pseudo yp map; it uses project only. Cedar10.1 expects to find its .mesa (and other) files using the path /project/cedar10.1/release, so you must add cedar10.1 to your project yp map.

Links

# cd /

# ln -s /fsrvr/project ./project

# mkdir pseudo

# cd pseudo

# ln -s /fsrvr/xrhome ./xrhome

Links needed on all Workstations

# cd /usr/include

# ln -s /fsrvr/xrhome/INSTALLED/INCLUDE/xr ./xr

# ln -s /project/cedar10.1/include ./cedar

THE CEDAR ENVIRONMENT IS NOW INSTALLED.

Appendix A

The following is either a list of files or a description of the contents for the various directories on the Cedar10 distribution tape.

xrhome/R←V.X/ (R - the current release number, i.e. 2, 3

V - the current version number, i.e. 12, 14, 0)

Code for the Portable Common Runtime (PCR)

/project/imagerfonts/

xerox/

diagnostic pressfonts xc1-1-1

graphics ps xc1-2-2

internal tiogafonts xc1-3-3

In these directories are the various font files

cedar10.1/

bin/

BasicViewersWorld kbd←mode tiogaxopen

ccc ldhide ToolsWorld

CedarCommander LocalShell withdrawxviewers

cedarrpcgen migrationtool X11ViewersWorld

CedarSetUp msScript xadobe

cedarxcommander PackageScript XCedar10.1Commander

cedarxscanner peekcedar XCedar10.1DynamicViewers

cedarxviewers pseudokeyboard XCedar10.1HostWorld

cliphack quitxcedar XCedar10.1PackagedViewers

CommanderWorld RawViewersWorld XCedar10.1ReOpen

do-cedar-command RemoteDebugTool XCedar10.1ServerViewers

ensure-cedar-server RemoteViewersHostWorld XCedar10.1Withdraw

FixPackage SetSticky xcredentials

GENcedar setupnewuser xmaintain

GENdevcedar slate XRDBX

GenerateCedarScript StartX

GenerateCedarScript-Aux StartXPen

bin/sun4/

cedarrpcgen

doc/

CedarPrimer.interpress

CedarPrimer.ps

README

include/

CedarExtra.h

InstallationSupport.h

mesa.h

lang/

ld (a version of ld that handles many more symbols)

lib/

cpp

cpp.c

cpp.MakeIt

newaccount/

.cshrc

.login

release/

Code for the various Cedar Applications

scripts/

cedar.login

src/

,LocalShell.c LocalShell.c Mx.Local.1

,Makefile LocalShellOld.c

BecomeConsole.c Makefile

src/SCCS

s.LocalShell.c s.Makefile

top/

bringover

disable

enable

README

.openwin-menu .xbitmap2 .Xmodmap

.twmrc .Xdefaults .xmodmaprc

.xbitmap1 .xinitrc

printing10.1/

Code for the various Printing Applications